root android jelly bean update

Root I747MVLDMF1 Bell, Rogers and Telus Galaxy S3 4.1.2 Jelly Bean Update, Root Injected Stock

This is the tested working root method for the Canadian Samsung Galaxy S3  (Bell,Rogers, Telus, and Sasktel) SGH-I747 variants that already received or updated to 4.1.2 Jelly Bean. The best best part of this rooting method is that it doesn’t trip the system’s binary flash counter from your Samsung Galaxy S3 I747 phone, tripping that binary counter leads to voids the warranty. Although, it can be reset actually, but for those beginners and not that much tech-savvy is quite irritating and risky on some part. Unlike to any other root method, of which the phone can’t accept future OTA update anymore, but using this root process you don’t to worry about any OTA updates coming.

This rooting technique uses the official firmware packaged and simply injected the root file  onto it.  This has been tested since the 4.0.4 Ice cream Sandwich and has still  proven worked perfectly on the latest 4.1.2 Jelly Bean updates. This root method is developed by [MrRobinson] (XDA-highly recognized contributor) from his original thread here.

Root Procedure: Canadian Galaxy S3 4.1.2 Jelly Bean

Disclaimer: Using this guide is solely at your own risk. Always proceed with precautions.

Grab Odin and USB Driver

  • Odin flasher – Odin3_v3.07
  • USB Driver –  Download
  • Use PC with Windows OS (Odin will not work on Mac and Linux OSX)
  • Make sure to fully recharge your battery
  • Use the original supplied USB cable for your Galaxy S3
  • Grab the root injected stock firmware according to your carrier provider.

Download and Extract the stock_root69.tar from the .7z file from the link below

New Jelly Bean Root injected Stock 4.1.2 I747MVLDMF1

Bell Image (This works with Canadian Virgin Mobile SGH-I747M)
Current I747MVLDMF1 (JB 4.1.2)
Mirror 1: Download root66_BMC_I747MVLDMF1.7z
Rogers Image
Current I747MVLDLMF1 (JB 4.1.2)
Mirror 1: Download root66_RWC_I747MVLDMF1.7z
Telus Image
Current I747MVLDMF1 (JB 4.1.2)
Mirror 1: Download root66_TLS_I747MVLDMF1.7z
Sasktel Image
Current I747MVLDLMF1 (JB 4.1.2)
Mirror 1: Download root66_BWA_I747MVLDMF1.7z

1. Run Odin on your PC desktop
2. Boot the Galaxy S3 into download mode screen for Odin.
Turn it off, once completely shut down hold down the ‘HOME’ + ‘VOLUME DOWN’ buttons and press the ‘POWER’ button for about 2 seconds until a WARNING! Screen appears. Press the ‘VOLUME UP’ button to continue or enter Download Mode. It will then display an – Android Robot and says ” Downloading.. DO not turn off target”

3. Connect the phone to PC via USB. Then make sure you can see as phone “Added” in Odin log box or a highlighted (blue color) COM:ID, once the device is detected or recognize with Odin.
4. In Odin window, DO Not tick ‘RE-Partition’ only Tick ‘Auto Reboot’ and ‘F. Reset Time’ and nothing else.
5. Now load the root injected stock ROM.
Click odin’s PDA button then select the root69.stock_Telus_I747MVLDMF1.tar

(odin sample only)



6. Click on “Start” to begin flashing.
7. Wait until the flashing finishes, DO NOT remove nor touch anything unless it completely finishes.
8. Remove the phone from PC once rebooted.

source: smartphonejam.com

Leave a Reply

Your email address will not be published. Required fields are marked *