Sometimes when your tired enough into rooting and modifying your Galaxy Note 2, there are circumstances that you need to unroot it or restore to its original factory default settings. There are some important factor why you root your Galaxy Note, this is because you need to install an Apps from Play Store that requires root before you can actually put it unto your device. But there are downside into rooting such as voiding the device warranty, sometimes it will not accept any software update. So, the only solution for this is to restore back your Galaxy Note 2 to its original firmware as it does automatically removes root also.
Installing official or original firmware will automatically remove root to your Galaxy note 2 once after flashing. Since rooting and installing unofficial firmware already voids your device warranty, that’s because the binary flash counter was triggered when you root or flash any unofficial ROM.
Do I need to reset the Binary flash counter when already tripped?
Yes! If you need to completely restore back without a trace of any modification, you should reset the flash counter. You may check it via download mode – pressing and holding (volume down + home + power buttons) then press “volume up” buttonto continue. Look for the Custom Binary Download, it shows a count of how many flashing has made. If it’s not tripped then you may not need to reset it, but if it showed like 0/1 and modified, then you should reset it to 0 count. You can simply alter it using Chainfire’s Triangle Away apps, it’s free to download it here.
Is this method useful in any other way?
Aside from bringing back your device from using unofficial firmware, this is also useful for fixing soft-bricks. If you messed-up from rooting or installing modified ROM then you need to fix it by restoring back the original firmware and bring back your device to be useful again. You can also use this method if you can’t update your device from OTA update and its show software update failure or install interrupted. Using the stock ROM, it’s actually the same process like updating from OTA or Kies. The only differences that this is developers method, updating on OTA and Kies is end-users method.
Disclaimer: We should not be held responsible if anything happens to your device. Proceeding and Use of this guide is solely at your own risk!
Important Reminders before Restoring or Flashing a Stock ROM on Samsung Galaxy Note 2 T-Mobile SGH-T889
- Make sure that your Galaxy Note 2 battery is fully charge.
- Stock ROM packages comes in two formats the ‘Full-Wipe’ (delete your stored data after flashing) and the ‘Non-Wipe’ (it doesn’t delete your phone’s stored data) but it is highly recommended to make a back up of all important files stored from your phone’s internal memory – contacts, SMS, emails, apps, photos, videos etc. before flashing, no-matter if it is Full-Wipe or Non-Wipe stock ROM version, just to be safe and ensure that your stored data are in safe place if something went wrong during the flashing process. Use any data back-up apps to easily do this task.
- Use a PC or laptop that runs in Windows OS, with a good and perfectly working USB serial port. Odin will not work on MAC OS.
- Use the supplied USB cable for your Galaxy Note 2.
- Enable USB debugging from your phone’s settings. Go to Settings > Applications > Development, and tick the box that says ‘Enable USB Debugging’.
- Ensure that KIES is closed and not running in the system tray! Kies will interrupt and doesn’t like Odin, it will block you from flashing.
Grab your Samsung Galaxy Note 2 SGH-T889 (T-Mobile) Original Firmware or Stock ROM
Download it here ->you should only choose SGH-T889 Stock ROM
Install the USB Driver and Extract the downloaded stock ROM
Install the USB Driver first to get rid of flashing failures. Also need to extract the downloaded file which is packed in zip format, so that you’ll get the tar.md5 file. You can use winrar, winzip, 7zip or any tool you had in your computer.
Step 1: Run and Configure Odin
Run Odin downloader Odin3_v3.07 on your PC desktop. Watch out the check-boxes options on the right top of Odin, ensure that the ‘RE-PARTITION’ is unchecked, only the ‘AUTO-REBOOT and ‘F.RESET TIME’ checkboxes are both remained checked.
Step 2: Reboot your Galaxy Note 2 into Download Mode
To reboot the Galaxy Note2 into download mode , you need to turn the power off. After it completely shut down, just press and hold the Volume Down key, Home button and the Power ON/OFF button simultaneously.
You should then prompted into a warning screen and asking you to press volume up if you want to continue or volume down to cancel, just simply press volume up to get into download mode. The download mode then displays an Android robot and say’s “Downloading.. Do not turn off target!!”
Step 3: Connect your Galaxy Note 2 to Computer or Laptop
Once you already reboot the phone in download mode, simply connect the phone to your PC or laptop USB.
In Odin window – the ID:COM box will turn to blue color and indicates the COM port number and a word “Added” on a log box will prompt you that the device is already detected or recognized by Odin. Your COM port number might be different from mine. If you do not see a COM port number then there’s something missing or wrong. You may read again from the top of this post.
Step 4: Set and load and the binary .tar.md5 file
The stock ROM is pack in One .tar.md5 file only. Now, you need to just simply click on the PDA button, then browse to the folder where the .tar or .tar.md5 you have previously extracted and then select and load it.
Step 5:. Begin Flashing the stock ROM
Once if all set and ready to fire-up, hit the “START” button in Odin to begin flashing the stock ROM.
Do not ever interrupt the phone while already in flashing progress, like disconnecting the cable or turning off the device. Just wait until it completely finish.
Step 6: Wait for the word PASS!!
When the Stock ROM installation successfully completes, you will then see a word “PASS” in Odin. This indicates that the flashing was already finish, and on the log box it says “All threads completed. (succeed 1 / failed 0)”. The phone will just then automatically reboot, then it’s time to remove it from PC or laptop USB connection.
Confirm your fresh firmware installed by typing *#1234# or
Go to Settings>About Phone>Firmware info.
You can also do factory reset by dialing *2767*3855#.
Possible issues that you might encountered, this is based on my experience while flashing stock ROM on Samsung Android devices. These are just a few hints on how to resolved it.
Q: I got an error message that says “Set-up connection Failed” ?
A: 1. Check your USB connection from the phone to PC,
2. Connect to another PC USB port
3. Check and try to another USB cable
4. Re-install the USB driver.
Q: Odin just suddenly stuck in the middle of nowhere while in flashing progress, It isn’t responding at all?
A: Check for possible program that might interrupt the process, like disabling theanti-virus and closing any running programs.Try to use another PC or laptop,
Q: I experienced bootloop or the phone just stuck on Welcome Logo (phone always stop at bootanimation) and it won’t boot normally?
A: You can fix it via recovery mode option, do this:
Boot in recovery mode
1. Press and hold Volume Up, Home and Power button.
2. Use volume keys to select, Up and Down and Power or Home key to select the option
3. Select Wipe Data/Factory Reset using the Home button.
4. Next select the Wipe Cache Partition
5. Lastly, select Reboot System Now to reboot your Galaxy Note 2 in Normal mode.That’s it! Just let us know how’s it going.